help po on KSC G19

[llalmerol]

Help po mga masters!May nabili akong 2nd hand na KSC G19 upgraded na into metal slide w/ 2 mags. Nung tinesting namin ito b4 I buy(w/o using bbs) ok naman cya, kaya lang medyo mhina ung blowback. when I tried using greengas ng nasa haus na ako, dun ko na nakita ung mga defects. Pinuno ko ung magazine ng BBs & gas, after firing 4-5 shots,bglang may narinig akong SWOOSH...ung tipong naubos ung isang mag refill ko ng gas..talagang ubos. so andami pang natirang BBs. naglagay po ako ulit ng gas, ganun pa rin ubos ulit ung gas after 2 shots. Minsan naman, 2 BBs ung lumalabas sa barrel.Tapos minsan, nagbo blowback pa rin kahit wala ng BBs ung mag. I tried using the 2nd magazine, pero ganun p rin. Naisip ko baka may epekto nung nagpalit ng hammer spring ung original na may ari, so tinignan ko ung mechanisms, parang may naupod na dun sa hammer (ito po yata ung hammer na tumatama sa dun sa magazine valve). may nabibili po bang mga parts nito?i really need ur assistance mga sir/s sayang naman ung pinambili ko. ung original na owner nito ay nagtago na sa ibang bansa nung tumawag ako sa phone nya..=( Salamat po ng marami sa inyo..

[quaker]

there are lots of reasons why your G19 is bahaving that way, I'm not sure about the "swooshing" but loks like you've fired your gun and all the gas were spent creating a swooshing sound ... if thats the case then the slide, at that time, was unable to fully cycle so the notch that releases the mag valve to cut off air was unable to reset, thus spending all the gas in one shot. anyways this is just one reason and actual inspection of a gbb gunsmith is recommended

[Brutus]

I agree with Quaker, issues with your G19 might be caused by multiple reasons like:
1. Tension of the hammer spring due to usage or wrong installation( soft hammer spring causes blowback problems)
2. Mag catch might have a deep notch already causing the magazine not to latch in properly thus causing a leak when fired.
3. Magazine top rubber lip( touching the blowback chamber) needs replacement, because it is not forming a proper seal with the chamber any more
4. The recoil spring might be the stock version making a slow recoil of the slide

I hope this helps you

[llalmerol]

maraming salamat po sir sa info. Sa magcatch po ang problem, upod na kasi plastic lang.papalitan na lng po.thanks po ulit

[Glocker]

piece of advice sa mga balak bumile ng 2nd hand lalo na sa mga di natin mashadong kilala. wag na lang. bili ka n lang ng brand new, safe ka pa. its just me

[D3nc10]

Sir, I'd be very willing to help you and those who are in need of any KSC parts. We can acquire it directly from KSC Japan. Just tell me the gun model and refer to the manual for the part number. Ordering Cost would be at the most minimal and allow 2-3 weeks leadtime..

[llalmerol]

thanks mga sir sa ideas..i'll try to replace first the mag catch. pag may pagbabago, inform ko kaagad sa inyo mga pips..salamat uli

Sir D3ncio, text ko na lng po kayo..=)

[melbs]

sounds like something wrong with your blow back mech

yun sa ksc usp ko ganyan din, had to teflon the o ring in the blow back mech

[davedecap]

greetings to the gurus i' d like to pitch in a problem with my KSC Glock19 lately it has been double feeding bb's which makes it loss power. how do i fix this ? thanks

[narru]

Sir, I'd be very willing to help you and those who are in need of any KSC parts. We can acquire it directly from KSC Japan. Just tell me the gun model and refer to the manual for the part number. Ordering Cost would be at the most minimal and allow 2-3 weeks leadtime..

hello sir do u have this part for ksc glock 23f...PART NO. 78 po pla e2 sir..
http://i204.photobucket.com/albums/bb167/narru_2007/kscpart78.jpg
heres my contact number 09158575791

tnx sir..